-
2025-03-10 22:13:35
1. Appearance inspection: Regularly check the surface of the slag tank for wear, deformation, cracks and other obvious defects. Check the tank mouth, tank wall, tank bottom and other parts of the tank, if found that the depth of wear exceeds the prescribed range, or the appearance of length and widt...
-
2025-03-10 17:50:18
Crusher hammer head is one of the core parts of the hammer crusher, arranged in the hammer shaft of the crusher rotor, the hammer head in the high-speed operation of the crusher directly strikes the material, crushing the material into the appropriate size. According to the material, the crusher ham...
-
2025-03-10 17:20:28
In order to adapt to the high abrasion working environment, the rolling mortar wall is generally made of high manganese steel, high chromium cast iron and other wear-resistant materials. High manganese steel has good toughness and work hardening characteristics, in the material impact, the surface h...
-
2025-03-10 17:10:05
The rolling wall is mounted on the frame of the crusher, which is curved and moves relative to the crushing wall driven by the eccentric shaft. When working, the material is squeezed, impacted and ground between the crushing wall and the molar wall, and thus is gradually crushed. For example, in the...
-
2025-03-10 17:05:18
1. Equipment inspection: before lifting the slag tank, be sure to check the lifting equipment, such as crane lifting mechanism, braking device, wire rope and so on. Lifting mechanism should run smoothly, no jamming phenomenon; brake device is sensitive and reliable, can be quickly braked in an emerg...
-
2025-03-10 17:03:35
1. Converter steelmaking link: in the process of converter steelmaking, iron after a series of smelting operations such as oxygen blowing, will produce a large number of high-temperature slag. Slag tank at this time to take up the important task of holding these slag, usually made of casting process...
-
2025-03-10 17:01:43
In metal ore mining, such as copper ore, iron ore, etc., hammerheads are used to crush raw ores. Through the impact of the hammer head, the lumpy ore is crushed into smaller particles for subsequent beneficiation, refining and other process operations. Due to the high hardness of the ore, hammer hea...
-
2025-03-10 17:00:15
Hammer head is the core component of the hammer crusher, when the equipment is running, the high-speed rotor drives the hammer head to strike the material entering the crushing chamber. Under the impact of the hammer head, the material is broken into small pieces and thrown to the crushing plate for...
-
2025-03-10 16:58:15
1. Cleaning treatment: regularly remove the residual slag and impurities in the slag tank to prevent their accumulation in the tank, affecting the subsequent use, and aggravate the corrosion of the tank. Can use mechanical cleaning or chemical cleaning and other methods, but be careful that the clea...
-
2025-03-10 16:56:50
Slag tanks are mainly used to carry converter slag, refining furnace slag, and large ladle casting residues for continuous casting. The temperature of the slag is higher than that of the liquid steel under the conditions of the converter smelting process. After the smelting is finished, the temperat...
-
2025-03-10 11:46:04
高锰钢锤头
-
2025-03-07 22:13:39
Crusher hammerhead has remarkable features. Diversified materials, high manganese steel hammerhead toughness and can work hardening, high chrome alloy hammerhead high hardness, wear-resistant and corrosion-resistant. Forging optimised structure to enhance the toughness, casting can create complex sh...
-
2025-03-03 22:13:35
Ball mill high manganese steel liner plate three major features:1. high wear resistance, impact resistanceBall mill high manganese steel lining plate by scientific and reasonable alloy element formula, so that the ball mill lining plate has good physical and chemical properties, hardness of HRC...
-
2025-03-03 22:12:13
1. Avoid overloading: strictly in accordance with the rated capacity of the slag tank loading slag, overloading will make the slag tank to withstand excessive pressure, accelerated wear and tear or even lead to tank deformation, rupture.2. Smooth lifting: in the process of lifting the slag tank, to...
-
2025-02-28 22:13:35
High manganese steel liner is used to protect the ball mill cylinder, so that the ball mill cylinder from the direct impact and friction of the grinding body and materials, but also can be used in different forms of high manganese steel liner to adjust the movement of the grinding body, in order to...
-
2025-02-28 22:12:13
High manganese steel liner plate can be used in ball mill, crusher, loader, excavator, cutter, bulldozer bucket and blade, screw conveyor and other wear-resistant structural parts production equipment. It can be processed by gas cutting and welded in various ways. In spite of the high strength of th...
-
2025-02-28 17:48:48
Crusher hammers are responsible for material crushing and have distinctive features. In terms of material, high manganese steel hammer head has good toughness, and the surface can be hardened when impacted, which greatly improves the wear resistance; high chromium alloy hammer head has excellent har...
-
2025-02-27 22:13:38
衬板
Pусский
Whatsapp
Phone